Replacing the Battery

Uses one 3.0 volt “CR2” lithium

Petsafe Anti-Bark Collar Operating And Training Manual. PetSafe Anti-Bark Collar Warranty Card Operating Guide Features. Tone Correction option. Tone plus Static Correction options. 3 Training Modes (up to 6 levels of Static Correction). Patented Perfect Bark™ technology for the most reliable bark detection. May 25, 2017  How to use smart bark collar Atom Tech. 330 Yards Remote House Training Shock Collar PST008 User Guide - Duration: 5:17. How to Teach your Dog to Bark and STOP BARKING.

battery (Tri-Tronics #1181300).

Remove the collar strap from the

Bark Limiter. Unscrew the 2 screws

on the bottom of the Bark Limiter,

alternating between screws, until

the two halves can be separated.

Remove the old battery and install a

new battery, matching polarity.
NOTE: Replacing a battery

automatically switches the unit

on and you will see the light begin

to blink. If unit does not turn on,

you probably have the battery in

backwards; turn it around and verify

function again. Thirty seconds after

inserting the new battery, the collar

will become capable of stimulation.

You may wish to switch the collar

off.
Replace battery cover gently, making

sure the gasket is properly in place.

Tighten screws, alternating between

screws. It is very important in order

to maintain the waterproof integrity

of the Bark Limiter that you ensure

that the gasket is in place smoothly

and evenly around the perimeter of

the battery cover with no twists or

folds. Replace the collar strap.
NOTE: The O-ring on the screw

should be positioned under the

head of the screw before screws are

tightened.
Troubleshooting

Try these suggestions if your unit

is not working properly. If you are

still having problems, email us at

support@tritronics.com or call

1-800-456-4343.
The dog is still barking while wearing

the Bark Limiter.
• The collar may be switched off.

Be sure the unit is on.

• The collar is inactive for 30

seconds after switch-on or any

intensity change. Wait for the

collar to become active.

• The collar isn’t tight enough.

Tighten the collar strap.

• The intensity isn’t high enough.

Try the next level.

• Remember it takes 30 seconds

after changing intensity for the

collar to become active again.

• The contact points aren’t making

contact through the dog’s

undercoat. Use the long contact

points. Wiggle the unit on the

dog’s neck to work the contact

points through his coat.

The collar light isn’t blinking even

though I switched the collar on.

It is normal for the light to stop

blinking whenever the unit has not

been moved. This is the battery

saving sleep mode.

The collar is blinking while it’s on the

dog. Is it correcting him even when he

isn’t barking?

No. The blinking light just means

that the collar is switched on.

I can’t get the collar to switch off or the

intensity to change levels.

Be sure to press and hold the

switch firmly.

My dog’s skin is irritated where he has

been wearing the bark collar.
• Dogs with sensitive skin can

experience skin irritation if they

Tbi Pro Bark Collar User Guide Owner's Manual Instructions

wear a bark collar too long at any

one time, due to the mechanical

pressure of the contact points.

• Do not use the bark collar until

the irritation is cleared up.

• Do not use it for longer than 10

hours out of every 24 hours.

• If the dog gets wet while wearing

a bark collar, the chance of

irritation is increased.

• Using the short contact points

will reduce the chance of skin

irritation.

• Contact your veterinarian if the

skin irritation is especially severe.

OWNERS MANUAL

Indicator

Lights

On/Off

What Is A User Guide

Button

Bark

Sensor

Contact

Points

Switching the Collar On

Press the on/off button next to

the contact points. One light will

double-flash. The collar is now on.
Motion Detection and Sleep

Mode

To save battery life, the Bark Limiter

has a motion detector. The internal

motion detector will switch the

collar off automatically whenever it

is not being moved. However minor

movements will switch it back on.

The lights remain off (“sleep mode”)

unless either motion or barking is

detected.

Increasing Intensity

The Bark Limiter has five correction

levels. The blinking light indicates the

current level. To increase intensity,

press and hold the on/off button

until you see the next intensity light

glow. Release the button. After you

release the button the light for the

new level will flash confirming your

new setting. The intensity can be

increased only one level at a time.
Decreasing Intensity

When level 5 is reached the next

intensity change will move the

intensity back to level 1. Increase

the level until you reach the desired

intensity.
Checking Intensity
To see what intensity is selected

after the collar has been switched

on just move the collar. The light

matching the selected intensity will

begin blinking.

Features

• Compact, easy to use, rugged, and waterproof
• Five intensity levels – set intensity instantly with

a press of a button

• Bark Odometer

™

– Counts the number of

times your dog barks so you can determine its

effectiveness, even when you are not home, and

then adjust intensity as needed

• Internal Bark Sensor is activated by vocal cords

and designed to help minimize false stimulation

• Consistent and dependable so your dog receives

the same stimulation each and every time

• Easy-to-see light confirms on/off, intensity level,

and low battery

• Choice of long or short contact points for

differing coat thickness

• Strap adjusts easily for a perfect fit with any

size dog

• Built-in sleep mode extends battery life in

normal use

• Operates on one replaceable 3v-CR2 lithium

battery (included) – battery will last one year in

normal use

• 30-day money-back guarantee
• 1-year comprehensive warranty